Skip to main content
Sublimation - Conde Systems - 27 Years Expert Experience
0 items in shopping cart

Tile: Ceramic Sublimation Instructions for M018

Required Accessories

Heat Tape, PROSPRAY-II

Paper

DyeTrans Multi-Purpose or TexPrint

OUR INSTRUCTIONS ARE BASED ON USING A DK20S, DK3110 AND/OR A COUNTER TOP CONVECTION OVEN. TIMES AND TEMPERATURES WILL VARY DEPENDING ON WHICH EQUIPMENT YOU USE.


SECONDS

400
DEGREES

MEDIUM; PSI FOR AUTOMATIC PRESSES: 40
PRESSURE

Hover transfer under open heat press for 10 seconds to dry excess moisture.

Ceramic Tiles
Single Tiles (See Mosaic Tiles Section for Bison Tile Sheets)
PowerDriver: Ceramic

Required Accessories: DyeTrans Pro Spray or Heat tape 1/2” Nomex Felt Pad or 1/8” Heat Conductive Rubber
Recommended Paper TexPrint, DyeTrans - Do not use Jetcol high release paper.
Temp for all Tile: 400° Pressure for all Tile: Medium PSI: 40

Using Felt

2" x 2"
DyeTrans Basic Value Tiles, BT22A 3 minutes, using Felt


3” X 6”
Bison 5 minutes Using Felt 6 minutes Using Rubber
Premiere and IronClad* 6 minutes Using Felt 7 minutes Using Rubber

4" X 4"
Bison, Premiere and IronClad* 8 minutes using ½” felt underneath, transfer, then tile face down with 1/8” green pad on top
DyeTrans Basic Value Tiles 3.5 – 4.5 minutes Using Felt Use felt method only

6" X 6"
Bison, Premiere and IronClad* 9 minutes using ½” felt underneath, transfer, then tile face down with 1/8” green pad on top
Bison Wall Tiles Use Rubber 8.5 minutes Using Rubber
DyeTrans Basic Value Tiles 4.5 – 5.5 minutes Use felt method only
3” Round 4 - 5 minutes 4 - 5 minutes Rubber or Felt Method
6” Round 5 - 6 minutes 5 - 6 minutes Rubber or Felt Method

6" X 8"
Bison, Premiere and IronClad* 8 minutes Using Felt 9 minutes Using Rubber
DyeTrans Basic Value Tiles 4.5 – 5.5 minutes Use felt method only
IF Country of Origin – Mexico 8 minutes Using Felt 8 minutes Using Rubber

8" X 8"
Bison, Premiere and IronClad* 8 minutes Using Felt 9 minutes Using Rubber
DyeTrans Basic Value Tiles 4.5 – 5.5 minutes Using Felt Use felt method only
IF Country of Origin – Mexico 8 minutes Using Felt 8 minutes Using Rubber

8" X 10"
IronClad* 6.5 minutes Using Felt 7.5 minutes Using Rubber
Bison, Premiere 8 minutes Using Felt 9 minutes
DyeTrans Basic Value Tiles 4.5 – 5.5 minutes Using Felt Use felt method only
IF Country of Origin – Mexico 8 minutes Using Felt 8 minutes Using Rubber

12" X 12"
IronClad* 9 minutes Using Felt 11 minutes Using Rubber
Bison and Premiere 6.5 – 7.5 minutes Using Felt 11 minutes Using Rubber
DyeTrans Basic Value Tiles 9 minutes Using Felt Use felt method only

Rubber Method Instructions

1) Print the transfer.

2) If using heat conductive rubber, then cover the bottom of the heat press with a protective sheet of paper.

3) Lightly mist the transfer with DyeTrans Pro Spray or use heat tape. Place the transfer on the face of the tile, smooth wrinkles. Should you decide to use heat tape, be sure it does not overlap the image on the other side of the page. Improperly applied heat tape will cause the affected area of the transfer to be inhibited.

4) If using rubber, then place the tile face down onto the protective paper and apply the rubber to the back of the tile.

5) Press with Temp/Time/Pressure settings listed above.

6) Carefully remove tile from the press and allow to air cool.

You can press more than 1 tile at a time if you have 2 or more inches of empty space surrounding all four sides of the tile. Add 1 minute of dwell time for each additional tile used during an imprinting session. For example, to press four 4x4 tiles add 3 minutes for a total time of 11 minutes.
*Be careful with the timing, too long in the press may cause purplish discoloration.

Felt Method Instructions
1) Print the transfer.

2) If using felt, then place the felt on the bottom of the heat press and then place a protective sheet of paper on top of the felt.

3) Lightly mist the transfer with DyeTrans Pro Spray or use heat tape. Place the transfer on the face of the tile, smooth wrinkles. Should you decide to use heat tape, be sure it does not overlap the image on the other side of the page. Improperly applied heat tape will cause the affected area of the transfer to be inhibited.

4) If using felt: With the transfer attached to the face of the tile, place the tile face down on the felt pad.

5) Press with Temp/Time/Pressure settings listed above.

6) Carefully remove tile from the press and allow to air cool.

You can press more than 1 tile at a time if you have 2 or more inches of empty space surrounding all four sides of the tile. Add 1 minute of dwell time for each additional tile used during an imprinting session. For example, to press four 4x4 tiles add 3 minutes for a total time of 11 minutes.

*Be careful with the timing, too long in the press may cause purplish discoloration.

If you are mounting these tiles and want to use grout: Un-sanded grout should be used. Tiles can be cleaned with any household non-abrasive cleaner and a soft cloth or sponge.

NOTE: Do not use grout for IronClad tiles, especially colored grout which will stain the tiles. Mortar, glue or silicone are recommended.

Updated: August 19, 2016

© Copyright 2024 Condé Systems, Inc. All Rights Reserved.
About  |  Blog  |  Terms & Conditions  |  Privacy  |  Support  | Feedback